If it's an entry sensor you're installing, Ring will ask what kind of door it is to apply the right sort of security to it — if it's your front door, for instance, it will use an entry countdown when you open the door while the base station is in Home and armed mode. If it’s the back door that's opened in this mode, the alarm will sound immediately.
The Ring Pro captures video at 1080p and has a 160-degree field of view. It uses three infrared LEDs to provide up to 30 feet of night vision and has a built-in motion sensor, a microphone, a speaker, and an interior chime. The camera uses 802.11n circuitry (2.4GHz and 5GHz) to connect to your home Wi-Fi, and requires a two-wire 16-24 volt power source (the same power source used for traditional doorbells). In addition to the camera, there's a doorbell button on the face of the device surrounded by an LED ring that glows blue when the button is pressed. There are two terminals on the back, and a setup button on the right side that you can get to by removing the faceplate.
I started with the extra power pack that gets installed inside and connected to your door chime. It was the more complex part of the installation and involved a very tall ladder but it went well. I was impressed that the ring doorbell came with everything you need to install it – including the drill bit AND a screw driver. It even has extra bits you MIGHT need (like extensions wires and extra screws). I also really appreciated how everything was in separate baggies for which part of the install you were doing and was very well labeled (extras were labeled as extras, pro kit wires in one bag, doorbell wires and screws in another). I was unable to fit the power kit inside my chime housing but it doesn’t look bad attached to the wall just outside the chime housing (see picture). It’s just a bit larger than a matchbox.
Most people don't have their wifi routers right near the front door so it can be a challenge getting a strong wifi signal to the Ring Doorbell. The other challenge is that the wifi signal must extend beyond the inside of the house and through building materials like bricks, siding, insulation and wood. So even if you have a strong signal inside your house it doesn't mean that your going to have a strong wifi signal outside your home.
Ring’s motion sensors and contact sensors are much more traditional than Nest’s, which cleverly combine the two into a single device that also adds a nightlight. Nest’s base station also combines the keypad with it and adds even more motion detection sensors – Ring’s separate base station and keypad approach is almost clumsy in comparison. But it is possible to add multiple keypads to the Ring system, so you can have one at each entry way or in your bedroom if that’s a more convenient place for it. The keypad can be placed flat on a table or mounted to the wall, and uses a simple MicroUSB cable for power. Its internal battery lasts between six and twelve months, according to Ring, so it’s possible to install it in a location that doesn’t have an accessible power outlet and just charge it occasionally.
The beauty of all Ring products is that they’re free of long-term contracts and completely integrated with the user’s everyday tech. In other words, this ain’t your grandpa’s home security system. For no additional cost, the online home base will alert any selected users and devices when there’s unwanted movement in and around the house. For an additional $10/month, Ring users are upgraded to unlimited video recording (should they add a Ring doorbell or floodlight cam) and 24/7 professional monitoring from the Ring HQ.
Even if you experience a power outage, both security systems will continue to work thanks to cellular connectivity. This feature is available from Nest for an additional $5 per month or $50 for the year. Ring includes this feature as part of their Protect Plus plan. Nest’s backup battery will last for 12 hours, while Ring’s will last for 24. With a longer battery life and an included cost, Ring is the clear winner here.
Once your trial of ring video recording ends, you can no longer access past events without a paid subscription. That's not such a big deal until you realize what counts as a "recent event". If you don't press the button within about 5 seconds of getting a motion alert, you missed your shot and now it's a past event. Say the UPS guy comes, presses the doorbell and walks off immediately. Your phone properly notifies you that somebody is at your door, but you've got something in your hands, or your phone is in your pocket or any other distraction is going on that takes 5 seconds to finish. By the time you hit the notification banner and go into the app, it will take you to a screen that says you need a paid subscription to see past events. Earlier today I got a notification WHILE holding my phone, clicked it immediately, but the live video loaded slowly and by the time it did load, the "event" was considered done and it took me to the screen saying I needed to pay. I have no problem paying to record everything and be able to pull up events from hours, days or weeks ago, but needing to pay because 5 seconds went by and the app loaded slowly is a rip-off. This is a $200 item which replaces a $5 hardware store doorbell, and the ONE thing it's supposed to do (show you live video of rings or motion events at your door) doesn't work about half the time without paying extra. There needs to be about a 30 second window at minimum where you can see what's going on without having to pay extra.